Skip to main content

2003 Honda Odyssey Key Fob Remote Programming Instructions


Here are the programming instructions for a 2003 Honda Odyssey Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog. If you like what we provide please forward on to your friends & family and share via the social media icons below; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE:  G8D-440H-A




2003 EX Model with Factory Installed Keyless Entry System. 

 Note:
 This system will accept up to three remotes. The remotes are stored in a stacking-type memory. If a fourth remote is programmed  the first remote will be erased.


 1. Turn ignition switch to ON (II)

  2. Within 4 seconds  press the LOCK or UNLOCK button on one of the remotes.Make sure remote is aimed at the receiver near the glove box.

 3. Within 4 seconds turn ignition switch to LOCK (0)

 4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used in step 2

 5. Within 4 seconds turn the ignition switch to ON (II)

  6. Within 4 seconds press the LOCK or UNLOCK button the same remote.  Make sure the power door locks cycle to confirm you are in programming mode.  Press the LOCK or UNLOCK button again.

 7. Press the LOCK or UNLOCK button on each remote you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.

  8. Turn the ignition switch to LOCK (0) to exit programming mode.

   9. Test remote(s)


 2003 LX Model with Dealer Installed Keyless Entry System.

 1. Turn ignition switch to ON (II)

 2. Press the LOCK or UNLOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)

 3. Turn ignition switch to LOCK (0)

 4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used in step 2

  5. Turn the ignition switch to ON (II)

 6. Press the LOCK or UNLOCK button the same remote.  Make sure the power door locks cycle to confirm you are in programming mode.

 7. Press the LOCK or UNLOCK button on each remote you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.

   8. Turn the ignition switch to LOCK (0) to exit programming mode.

  9. Test remote(s)

Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.

ENTER YOUR CITY NAME TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU
By Keyless Entry Remote Inc

Popular posts from this blog

General Mercedes Benz Key Fob Remote Programming Instructions

Here are general programming instructions for Mercedes Benz Key Fob Remotes. Try these instructions on your Mercedes Benz, if they don't work, try to look for your specific year, make. & model.  If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

PLEASE NOTE THAT MOST MERCEDES BENZ KEYLESS ENTRY REMOTE KEY FOBS REQUIRE SPECIAL DEALER EQUIPMENT TO PROGRAM.  YOU WILL MOST LIKELY HAVE TO GO TO THE DEALER TO HAVE THEM PROGRAM THE REMOTE TO YOUR VEHCILE.  ALSO, PLEASE CHECK WITH YOUR DEALER TO SEE IF THEY WILL EVEN PROGRAM A REMOTE YOU PURCHASE OFF THE INTERNET, A LOT OF MERCEDES DEALERS ARE JUST REFUSING TO PROGRAM KEY FOBS UNLESS YOU PURCHASE FROM THEM.

ORDER THIS KEY FOB PART NUMBER HERE: 1407601406





1  Place your key in …

Did Your Car Remote Stop Working?

Did your car remote stop working?  It can be a pain in the "you know what" when your vehicle key fob remote stops working.  I mean, come on, it is so hard to just put your key in the door and unlick it manually, lol!  But seriously, we have come to rely on our key fobs and that is why when they stop working it can be very frustrating.  Here are a couple tips to try and get your key fob working again:

1)  Replace the battery.Most vehicle key fob remotes just split open.  Usually there is a small slot on the side of the remote where you can stick a small flat head screw driver in and pop the case open.  There you will find a  small coin battery.  The coin batteries have numbers on them, usually something like CR2032.  That is the battery size.  You can find new coin batteries pretty much anywhere these days, and if you are having a hard time finding them at a local store you can order them online at keylessentryremotefob.com. 

2)  Reprogram the remote.  Sometimes when the bat…

2005 Jeep Grand Cherokee Key Fob Remote Programming Instructions

Here are the programming instructions for a 2005 Jeep Grand Cherokee Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog. If you like what we provide please forward on to your friends & family and share via the social media icons below; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE:  56038768AD


FOR REMOTE PART (LOCK, UNLOCK, PANIC, TRUNK)

PLEASE NOTE: YOU MUST HAVE ONE WORKING REMOTE TO ADD ONE MORE TO THE SYSTEM.  IF YOU DO NOT HAVE ONE WORKING REMOTE RIGHT NOW THEN THESE INSTRUCTIONS WILL NOT WORK.  YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER. 

1.  Press LOCK button 5 times at 2 second intervals to resynchronize remote.

2.  Insert key into the ignition switch. Turn ignition to the RUN position
    (as far as you can go without cranking engine). Wait for ignition chime…