Skip to main content

2000 Volvo V40 Key Fob Remote Programming Instructions


Here are the programming instructions for a 2000 Volvo V40 Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

ORDER THIS REMOTE PART NUMBER HERE: 9166199




Instructions

1  Make sure all doors are closed, as well as the hood. Make sure the tailgate or trunk is locked. Get into the car and lock all doors.

2  Insert the key and turn it from the insertion position (position I) to the "on" position (position II - not the "start" position) five times. In other words, all the dash lights come on, but the engine doesn’t start. When you turn the key to ON the fifth time, leave it there. You have 10 seconds to perform this whole step.

3  Hold down each remote button for a second or two, so the car identifies those buttons as the     ones to respond to. If you want multiple remotes to work for that car, you’ll need to hit the buttons on each of them in rapid succession (all within 5 seconds) as well. You can program up to three remotes per car.

4  Get new batteries if the above doesn’t work, and try it again. If you already have new batteries in the remote, then proceed to the next step.

5  Press and hold down the odometer reset button.

6  Turn the ignition switch to the RUN position.

7  Release the odometer button while the service reminder light (SRL) flashes. Don’t wait until the flashing stops to release the odometer button. If you did that, you waited too long.

8  Turn the ignition off.

WE HAVE HAD MANY PEOPLE STATE THAT THESE PROGRAMMING INSTRUCTIONS DO NOT WORK.  WE FOUND THIS INFORMATION ON A VOLVO FORUM:

There is a software that needs to be downloaded to the car. When the remote is purchased at the dealer it comes in a plastic package. That plastic package has a sticker on it. The sticker contains id codes.

There are two codes one is 16 digits/letters and the second one is 8 digits/letters.

Without this sticker the dealership can not program the remote/key to the car. If you buy a key elsewhere, make sure it has the codes included.

Unfortunately you cannot program a remote yourself.


Having trouble programming the remote or just want a professional to program the remote for you? Enter your city or zip code in the search box below to find a professional key fob installer in your area.

ENTER YOUR CITY NAME OR ZIP CODE TO FIND A
PROFESSIONAL KEY FOB INSTALLER NEAR YOU



Popular posts from this blog

General Mercedes Benz Key Fob Remote Programming Instructions

Here are general programming instructions for Mercedes Benz Key Fob Remotes. Try these instructions on your Mercedes Benz, if they don't work, try to look for your specific year, make. & model.  If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

PLEASE NOTE THAT MOST MERCEDES BENZ KEYLESS ENTRY REMOTE KEY FOBS REQUIRE SPECIAL DEALER EQUIPMENT TO PROGRAM.  YOU WILL MOST LIKELY HAVE TO GO TO THE DEALER TO HAVE THEM PROGRAM THE REMOTE TO YOUR VEHCILE.  ALSO, PLEASE CHECK WITH YOUR DEALER TO SEE IF THEY WILL EVEN PROGRAM A REMOTE YOU PURCHASE OFF THE INTERNET, A LOT OF MERCEDES DEALERS ARE JUST REFUSING TO PROGRAM KEY FOBS UNLESS YOU PURCHASE FROM THEM.

ORDER THIS KEY FOB PART NUMBER HERE: 1407601406





1  Place your key in …

Did Your Car Remote Stop Working?

Did your car remote stop working?  It can be a pain in the "you know what" when your vehicle key fob remote stops working.  I mean, come on, it is so hard to just put your key in the door and unlick it manually, lol!  But seriously, we have come to rely on our key fobs and that is why when they stop working it can be very frustrating.  Here are a couple tips to try and get your key fob working again:

1)  Replace the battery.Most vehicle key fob remotes just split open.  Usually there is a small slot on the side of the remote where you can stick a small flat head screw driver in and pop the case open.  There you will find a  small coin battery.  The coin batteries have numbers on them, usually something like CR2032.  That is the battery size.  You can find new coin batteries pretty much anywhere these days, and if you are having a hard time finding them at a local store you can order them online at keylessentryremotefob.com. 

2)  Reprogram the remote.  Sometimes when the bat…

2005 Jeep Grand Cherokee Key Fob Remote Programming Instructions

Here are the programming instructions for a 2005 Jeep Grand Cherokee Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog. If you like what we provide please forward on to your friends & family and share via the social media icons below; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE:  56038768AD


FOR REMOTE PART (LOCK, UNLOCK, PANIC, TRUNK)

PLEASE NOTE: YOU MUST HAVE ONE WORKING REMOTE TO ADD ONE MORE TO THE SYSTEM.  IF YOU DO NOT HAVE ONE WORKING REMOTE RIGHT NOW THEN THESE INSTRUCTIONS WILL NOT WORK.  YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER. 

1.  Press LOCK button 5 times at 2 second intervals to resynchronize remote.

2.  Insert key into the ignition switch. Turn ignition to the RUN position
    (as far as you can go without cranking engine). Wait for ignition chime…