Skip to main content

2009 Chevrolet Silverado Key Fob Remote Programming Instructions


Here are the programming instructions for a 2009 Chevrolet Silverado Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE: 15913420



Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.

1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
    PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
    REMOTE KEY LEARNING ACTIVE  displays

4.  Press and hold the lock and unlock buttons on the keyless remote at the same
     time for approximatley 15 seconds. A chime will sound indicating that the remote is
     programmed.

5.  To program additional remotes at this time repeat step 4.
      This vehicle can have a maximum of eight remotes programmed.

6.  To exit programming mode turn key off and remove key.
     Test remote(s).

Use this Procedure for Vehicles without
Drivers Information Center Buttons


To access this display, the vehicle must be in Park (P) with key in the on position (as far
    as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds.
    The message  REMOTE KEY LEARNING ACTIVE  will display

3.  Press and hold the lock and unlock buttons on the first keyless remote at the same
     time for approximately 15 seconds. A chime will sound indicating that the remote is
     programmed.

4.  To program additional remotes at this time repeat step 3.
     This vehicle can have a maximum of eight remotes programmed.

5.  To exit programming mode turn key off and remove key.
     Test remote(s).


Was This Information Useful?  Please take a moment to Like / Follow us and share via social media below. It is people like you that help spread the word about us.  It helps so much!  Thanks for visiting and sharing with your friends and family!


Subscribe To Our Social Networks For Special Discounts, Offers, & Contests!

        
By Keyless Entry Remote Inc

Popular posts from this blog

General Mercedes Benz Key Fob Remote Programming Instructions

Here are general programming instructions for Mercedes Benz Key Fob Remotes. Try these instructions on your Mercedes Benz, if they don't work, try to look for your specific year, make. & model.  If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog and if you like what we provide please forward on to your friends & family; people like you are our best advertising tool!

PLEASE NOTE THAT MOST MERCEDES BENZ KEYLESS ENTRY REMOTE KEY FOBS REQUIRE SPECIAL DEALER EQUIPMENT TO PROGRAM.  YOU WILL MOST LIKELY HAVE TO GO TO THE DEALER TO HAVE THEM PROGRAM THE REMOTE TO YOUR VEHCILE.  ALSO, PLEASE CHECK WITH YOUR DEALER TO SEE IF THEY WILL EVEN PROGRAM A REMOTE YOU PURCHASE OFF THE INTERNET, A LOT OF MERCEDES DEALERS ARE JUST REFUSING TO PROGRAM KEY FOBS UNLESS YOU PURCHASE FROM THEM.

ORDER THIS KEY FOB PART NUMBER HERE: 1407601406





1  Place your key in …

Did Your Car Remote Stop Working?

Did your car remote stop working?  It can be a pain in the "you know what" when your vehicle key fob remote stops working.  I mean, come on, it is so hard to just put your key in the door and unlick it manually, lol!  But seriously, we have come to rely on our key fobs and that is why when they stop working it can be very frustrating.  Here are a couple tips to try and get your key fob working again:

1)  Replace the battery.Most vehicle key fob remotes just split open.  Usually there is a small slot on the side of the remote where you can stick a small flat head screw driver in and pop the case open.  There you will find a  small coin battery.  The coin batteries have numbers on them, usually something like CR2032.  That is the battery size.  You can find new coin batteries pretty much anywhere these days, and if you are having a hard time finding them at a local store you can order them online at keylessentryremotefob.com. 

2)  Reprogram the remote.  Sometimes when the bat…

2005 Jeep Grand Cherokee Key Fob Remote Programming Instructions

Here are the programming instructions for a 2005 Jeep Grand Cherokee Key Fob Remote. If you need an extra Key Fob or Replacement Fob for any vehicle you might have visit us at Keylessentryremotefob.com You can also leave comments or suggestions at the bottom of this blog. If you like what we provide please forward on to your friends & family and share via the social media icons below; people like you are our best advertising tool!

ORDER THIS KEY FOB PART NUMBER HERE:  56038768AD


FOR REMOTE PART (LOCK, UNLOCK, PANIC, TRUNK)

PLEASE NOTE: YOU MUST HAVE ONE WORKING REMOTE TO ADD ONE MORE TO THE SYSTEM.  IF YOU DO NOT HAVE ONE WORKING REMOTE RIGHT NOW THEN THESE INSTRUCTIONS WILL NOT WORK.  YOU WILL HAVE TO GET IT PROGRAMMED BY A LOCKSMITH, MECHANIC, OR DEALER. 

1.  Press LOCK button 5 times at 2 second intervals to resynchronize remote.

2.  Insert key into the ignition switch. Turn ignition to the RUN position
    (as far as you can go without cranking engine). Wait for ignition chime…